超聲波測距儀是 完全適用于家庭裝修、買空調時計算面積體積、房地產代理商或 建筑工人 所必須的、需要的快速測量房間和房間面積的工具， 超聲波測距儀能夠測量直線距離從0.50M到18M。(1.5英尺—60英尺) 超聲波測距儀是利用發射超聲波到被測物體，然后計算超聲波往返時間來確定測量距離的。
參考參數：
測量范圍：50厘米~18米
誤差:千分之五
分辨率:0.01米
測量距離:18米
距離之和:180.00米
計算面積:18×18平方米
計算體積：1800.0立方米
電池：9v
發射頻率：40kHz
度：±0.5%
分辨率：0.01m
工作溫度：0°C ~ 50°C
產品介紹：
超聲波測距儀在國外被稱之為“電子卷尺”，適用于建筑、裝修、工程等場所，能夠做到傳統卷尺力所不及的測量。本店銷售的超聲波測距儀根據廠家提供的數據顯示已經是目前國際上性能比較好的產品，而且在歐美市場的占有率相當高，比起其他品牌的測距儀在超聲波發射角、抗干擾處理等方面上有了明顯地差別。
型號:CP-3007
出口產品,英文說明書!如果需要中文說明書的以電子文檔方式提供.
紅外測距儀 超聲波測距儀 工程測距 無線測距 真方便！
測量時注意事項：
1.超聲波測距儀測試的是障礙物離機器底部的距離，而不是頂部距離，如果以頂部為準，你會發現顯示距離與實際距離永遠有那么10幾cm的誤差，呵呵。
2.測量時機身與墻壁盡量保持垂直，尤其是所測距離較遠時，越垂直，測量數據越高，反之斜度越大，誤差越大。長距離測量時建議開一下激光定位以盡量保持垂直
新款CP3007激光測距儀 超聲波測距儀
詳細中文使用說明書：
CP-3007超聲波測距儀使用指南
準備
安裝電池
你的測距儀需要9V的電池。為了更好的使用和延長壽命，我們建議你使用堿性的電池。
請根據以下步驟安裝電池：
1. 按照電池室箭頭的方向去放；
2. 蓋是推滑開的，電池室里有正負（+和-）兩極，
3. 打開蓋子
4. 當顯示電量低時或者是測距儀不能運行時，請更換電池。
警示：如果是一個月或者是一個月以上不用，請把電池取出，以免電池長時間不用漏液損壞儀器。
測距儀的穩定化處理：
此儀器對溫度和濕度很敏感，在使用之前，等15—30分鐘直到測距儀穩定到室溫。
使用
測距儀的開關：
要打開此儀器，請按“MEASURER”即使在黯淡的光線下也能很容易顯示屏幕，等電壓穩定了，就可以看到當時的環境溫度。
30秒如果不用就自動關閉。
測量時：
1.請按一下“MEASURE”，此儀器的雷達將會測出儀器到達所要測的另一端。
2.使儀器的底部靠近墻壁，大概是天花板到地板的距離。確保你測量的距離之間沒有障礙物，你的頭或者你的手不要在測量儀的前面。
3.重復按“FEET”或者“METER”， “FEET”表示以英尺測量，或者是出現“METER”表示以米測量。
說明：
測量儀的顯示一般是在30秒左右，如果你更換另一個模式也是要30秒左右。
如果你測量的范圍小于2英尺（0.5米）或者是大于60英尺（18.288米）將會顯示“ERROR”
測量小秘訣：
有些窗簾可以吸收聲波，導致測量儀測量不準。如果你在有窗簾的室內進行測量的話，請先把窗簾放到窗戶的另一面，還要把窗戶關上。
如果測量的距離中有障礙物的話，那超聲波測量出來的數據是不正確的，比如說桌子，椅子，或者其他的障礙物。如果你不確定你測量的是否正確，那你就從不同的角度進行多次測量。
如果你測量的不是平整的地方或者是很窄的角落，那你得出的數據就是有誤的。
如果要測量的距離大于60英尺（18.288米）那就選擇房子的中間的一點，比如說:從中點向每一面測量，然后加起來就可以了。
減小測量誤差：
1. 按照這些步驟用“測量”來衡量一個尺寸
2. 按一下“STORE”鍵，你就可以把測量的數據存儲在內存卡M1，M2或者M(jìn)3卡里面。
3. 如果有必要，就重復上面的和第二步驟去存儲數據。
4. 如果想把數據存儲在哪個內存卡，就按M1，M2或者M(jìn)3卡。這樣數據就存在里面了。
5. 如果想存儲新的數據的話，那就直接把原來的數據刪除就可以了。
6. 如果要?jiǎng)h除所有的數據的話，那就按“ALL MEMORY CLEAR ”按住3秒，然后全部的數據還有M1，M2, M3之類的都會暫時消失。
注意： 刪除后日期和聲音是不能保存的
測量音量：
想測量住房的音效，先測量高度，寬度，長度，然后儲存每個數據到不同的內存卡請看到“Saving a Measurement”,然后按“VOLUME”，音效的計算和存儲就出來了。
測量面積：
根據以下步驟找兩個空的存儲空間：
1. 測量的高度和寬度就存儲在M1和M2的內存卡上，按“AREA”“M1”和“M2”,數據就存儲了。
加減乘除的存儲
1. 測量出來的任何兩個尺寸，保存在M1和M2，
2. 按“ALL MEMORY CLEARE”鍵
3. 按“M1”加“M2”加其他要加的數據或者是按“M1”減“M2”減其他要減的數據，這樣要加的或者要減的數據就出來了。
4. 如果想存儲另外的數據或者是想清除內存請按“ALL MEMORY CLEARE”就可以了。
使用激光：
要使用激光，請按“LASER”，如果5秒鐘不動的話會自動關閉激光的功能。
規格：
電池：1個9V的電池。（不包括）
測量儀的單位是英尺和米。
度：0.005+1
頻率：40千赫
測量范圍：0.50到18.288米
典型的規格，個別有可能會改變，規格如有更改,恕不另行通知改善。
注意：
激光發射的650海里為可視激光波長。
別盯著激光光束看,也不要用激光射任何人的眼睛
CP-3007 Ultrasonic Distance Measurer OWNER'S MANNUAL
PREPARTION
INSTALLING BATTERIES
You measurer requires 9V battery(not supply) for power.
For the best performance and life,we recommend alkaline battery.
Follow these steps to install a battery.
1.Slide the battery compartment cover in the direction of the arrow to remove it.
2.Snap the battery in the compartment.As indicated by the polarity symbols(+and-)marked inside.
3.Replace the cover.
4.When Low Battery Icon appears or the measurer stops operating properly,replace the battery.
Caution: If you do not plan to use the measurer for a month or more,remove the battery ,Battery,Batteries can lesk chemicals that can destroy electronic parts.
STABILIZING THE MEASURER
You measurer is sensitive to changes in temperature and humidity.Before you use the measurer,wait about 15~30minutes for it to stabilize to the current room's temperature.
OPERATION
TURNING THE MEASURER ON/OFF
To turn on the measurer,press MEASURER, can light up the display screen for easy viewing even in a dimly lit area.After power on,the unit display current Environment temperature.
The measurer turn itself off if no key is pressed within about 30 seconds.
TAKING A MEASUREMENT
1.Pree MEASURE to turn on the unit.The measurer beeps then the distance between the measurer and the piont you measured appears.
2.Hold the bottom of measure flat against a wall,about hafway between the point you want to measure and that your head or hands do not block the front of the measure.
3.Repeatedly preesFEET/MERERuntilFEETappears(to measure in feet)or untilMETERappears(to measure in meter)
Notes:
The measurement appears for about 30 seconds(or longer if you press another key)
ERROR might appear if you try to measure a distance shorter than the range of 2 feet(0.5m)or longer than 60 feet(18.288 meters)
Measuring Tips
Some type of curtains and blinds can absorb sound waves.
Causing measurements to be inaccurate.If you are measuring distances in a room with curtains.Open the curtains before measuring the distance to a window behind them.Also,be sure that the window is closed.
If there is not clear path between the points where you are measuring.You might receive a false reading from sound waves bouncing off objects such as chair,tables and objects with uneven surfaces .If you are not sure if a measurement is correct,move slightly to one side then measure the distance again.
If the surface of a wall you are measuring is not sold and flat,or if you are measuring in a narrow corridor.You might receive a false reading.If this happens， use a sold surface to measure or move to the center of the corridor.To measure a distance longer than 60 feet(18.288 meters) measure from the center of the room toward each side.then add the two measurements.
SAVINGA MEASURENT
1.Follow the steps under"Taking a Measurement"to measure a dimension.
2.PressSTOREthen a memory key(M1,M2,M3).M and the number of the memory location you choose (1,2or3)appear and the measurer stores the reading in that memory location.
3.If necessary,repeat steps 1 and 2 to save up to three measurements.
4.To display measurement stored in a memory location,press that memory key (M1,M2,M3).The measurement stored in that memory location appears.
5.To delete a measurement stores in a memory location， simply store a new one in its place.
6.To clear all stored measurements,hold downALL MEMORY CLEARfor about 3 seconds,the measurer beeps and M and the number of the memory location you chose (1,2or3)disappears.
Note:Data of AREA of VOLUME can not be saved.CALCUATING VOLUME
To find the volume of a room.Measure the height,width and the length of the room and store each measurement in a different memory location(see"Saving a Measurement "),Then press VOLUME,The volume calculation result appear.
CALCULATIONAREA
Follow these steps to find the area of any two stored measurements
1.Measure the width and length of a room and store the measurements in M1 and M2(see"Saving a Measurement").Press AREA,M1 and M2,the area calculation appear.
ADDING/SUBSTRACTING STORED MEASURENTS
1.Measure any two dimension of a room and store the measurements in memory locations 1 and 2(see"Saving a Measurement")
2.PressALL MEMORY CLEAR.
3.Press M1,+M2,then +to add the measurements,or M1,-,M2,then-to subtract them.The value of the calculation appears.
4.To clear the display and do another measurement,pressALL MEMORY CLEAR.
USING LATER
To have a laser pointer,press LASER.The laser pointer disappears automatically after about five seconds
SPECIFICATIONS
Power lx9V
Unit of measurement Feet or Meters
Accuracy 0.5%+1digit(2-60ft)
Working Frequency 40KHz
Working Temperature 0℃ to 43℃
Range 2 to 60ft (0.50 to 18.288m)
Specifications are typical;individual units might vary.
Specifications are subiect to change and improvement without notice.
Caution:
The laser emitted from the unit is visible laster of 650nm wavelength
Don't stare in to the laster beam and also don't shoot laster beam to any other 's eyes.
Class II laser product Output<lmw
Notes:
The product has passed EN60825-1
Corresonding label is affixd on the back of the unit.
