儀器特點：

靜液壓試驗機適用于各種塑料管材長期靜液壓試驗、管材液壓瞬時爆破試驗和長期恒定耐壓下熱塑性管材耐破壞時間的測定。我公司是國內做管材檢測設備較早的公司，當時具代表意義的是分壓技術，我公司是用儀表及電腦分別控制、多電閥控制、多功能控制。有的現在仍是的具體為：較早掌握分壓控制（各路壓力不一樣）技術。較早采用上下位計算機（雙計計算機）控制方式。較早采用與丹麥相同控壓方式。是各科研院所、質監部門的儀器。

合標準：

GB/T6111—2003《流體輸送用熱塑性塑料管材耐內壓試驗方法》

GB/T15560—1995《流體輸送用塑料管材液壓瞬時爆破耐壓試驗方法》

GB/T18742.1—2002《冷熱水用聚丙烯   第二部分：管材》

GB/T18742.2—2002《冷熱水用聚丙烯   第二部分：管材》

GB/T18742.3—2002《冷熱水用聚丙烯   第三部分：管件》

GB/T13663—2000  《給水用聚乙烯PE管材》

GB/T15558.1—2003《燃?xì)饴竦赜镁垡蚁㏄E管材》

GB/T18992.1—2003《冷熱水用交聯聚乙烯管道系統總則》

GB/T18992.2—2003《冷熱水用交聯聚乙烯管道系統管材》

GB/T10002.1—2006《給水用硬聚氯乙烯（PVC—U）管材》

GB/T10002.2—2006《給水用硬聚氯乙烯（PVC—U）管件》

GB/T18993.1—2003《冷熱水用氯化聚氯乙烯管道系統》

GB/T18993.2—2003《冷熱水用氯化聚氯乙烯管道系統》

GB/T18992.1—2003《冷熱水用氯化聚氯乙烯管道系統管件》

GB/T18997.1—2003《鋁塑復合壓力管鋁管搭接焊式鋁塑管》

GB/T18997.2—2003《鋁塑復合壓力管鋁管對接焊式鋁塑管》

ASTM D1598、ASTM D1599

性能介紹：

1）、每路一塊“微機控制單元”（真正的分路控制——一套系統控制多路時系統出問題時影響各路——現有些產品就用一套系統控制多路）微型計算機控制，可以在系統計算機不開機的情況下單獨設定、控制本路壓力、、時間等參數；時實顯示壓力、時間、狀態（八個）并將各參數數據存儲。（系統計算機脫機時數據丟失壓力數據——現有些產品脫機時據等于此段時間試驗白做）；同時判別升壓、補壓、泄壓、過壓、運行、結束、泄漏、爆裂八種試驗狀態；自動判別“試驗時間”（壓力在設定控壓公差帶內的時間）“無效時間”“剩余時間”等時間參數。同時自動調整“設定時間”與“時間”的關系使試驗只有在“時間”“設定時間”時試驗才自動停止（晚上節假日等時段內出現“故障時間”“無效時間”時系統在時間不到時停機）

2）、電磁閥，每路二支。由于采用了與德國、丹麥同步的按壓方式，一支升補壓電閥可根據程序和試驗情況，分別改變動作頻率和動作時間，使PE大口徑試樣的快速準確補壓得以實現。使設備適用范圍廣（Ф20—Ф630PE管）控壓高（±1%可達±0.001Mpa）的要求。

3）、丹麥水用壓力站一套，比國產水用試壓泵和有些廠家產品配的氣驅水泵（得用氣體驅動水）流量大、性能更好，壽命更長噪音低且不用氣泵（源）。

4）、航天部高傳感器每路一支，分辯率0.001Mpa及按壓設定值為±0.001Mpa。

5）、每路還有管路單向閥調流閥若干。

6）、多行數字顯示液晶屏、多道貯存通訊（含U盤貯存）、通訊協議更廣泛，表現在可和電腦（PC）、可編程控制器（PLC）、觸摸屏等大多顯示終端通訊

7）、品牌計算機一套，

本機特點及組成：

1、特點

1）、可連續無障礙工作，了試驗的完整性；

2）、支路間相互，便于操作和維護；

3）、單獨配備加壓水箱，使用純凈水通過主加壓泵往管材試樣中補壓，了管路中的水質，了管路件（如電磁閥、針閥、截止閥、單向閥）的使用壽命；

4）、使用自主研發的、的、脈沖占空比補壓技術，將升壓環節和補壓環節合二為一，減少了一個支路及器件，也就減少了器件損壞的幾率；

5）、使用臺灣產柱塞泵，噪音低，補壓快，工作時間短，間接了柱塞泵的使用壽命；

6）、在儀表控制基礎上配PC機（即計算機），采用串口與儀表聯接。

a、可繪制壓力時間曲線，

b、可實時查詢?nèi)我鈺r(shí)刻的控壓值，

c、可打印輸出報表，

d、可代替人工職守，當無人看管時（如夜間）自動記錄壓力值；

e、計算機機可停止工作，儀表仍然繼續工作。

2、設備的組成說明：

本試驗機由壓力控制系統、壓力源、恒溫介質箱、夾具和計算機五部分組成。

1）、壓力控制系統在控制柜中由加壓管路和電器控制兩部分組成。加壓管路由蓄能器、電磁閥、單向閥、過濾器、手動針閥、連接管路等部件組成。電器控制部分由數字控壓壓力表、溫度控制儀表、壓力傳感器、電磁閥、繼電器、過熱保護器、各種開關等組成。

2）、壓力源用來對主壓力系統按試驗條件提供總壓力。

3）、恒溫介質箱主要由箱體、循環泵、加熱器、冷凝器和溫度控制系統組成。箱體由不銹鋼內膽、噴塑外殼體（或不銹鋼）、保溫層、試樣支架和箱蓋組成。

4）、夾具為A型，的設計試夾具的拆裝更方便自如；楔型配合螺紋夾緊裝置使夾緊力更大。本系列夾具具有結構合理、夾緊速度快、密封、拆卸方便的特點。

5）、計算機配備的是品牌機，通過串口與控制柜相連。品牌機是聯保，各地網點均可維護。

工作原理

該機的工作原理是：

1）、設定主壓力儀表的控制壓力和范圍，使壓力源提供高于支路壓力的2～3MPa的壓力儲存在蓄能器中。

2）、按照試樣的環應力要求計算試驗壓力，并依此設定支路壓力儀表的控制壓力和范圍，運行后儀表控制電磁閥全導通，使試樣的壓力上升。設定壓力時進入補壓階段。

3）、補壓階段時電磁閥依據儀表數據斷續導通，使壓力源蓄能器中的壓力補充進試樣中。

4）、壓力源的壓力下降到設定壓力下，柱賽泵啟動工作到上停止。

5）、本機同時具有運行、停止、滲漏預警、破裂識別等功能，實現操作人員在試驗過程中可脫離實驗現場。當試樣出現滲漏、破裂時自動報警并自動關閉該路，其它各路試驗繼續正常進行，直到試驗完成。在同類機型中具有優良的性能價格比，是替代的理想產品。

6）、該機有串口可外配計算機，繪制壓力時間曲線，可實時查詢控壓值，可打印輸出報表，可代替人工職守，可當計算機機停止工作時，儀表仍然可繼續工作。但計算機機不直接控制電磁閥，須經過儀表控制，試驗時儀表不可停止工作。在做試驗過程中，還可關閉計算機機做其它商務業務，主機正常工作。當主機與計算機連通時，主機自動將數送給計算機機，對試驗不產生任何影響。

6）、水箱為主箱內加熱可加熱管的壽命，體外循環使水箱中的水溫均勻。恒溫介質水箱分單熱式和制冷制熱式兩種規格。本機為室溫至95℃

技術參數

1、主機壓力范圍：0001～10.000MPa   0001～20.000MPa（可任意調整）

2、水箱控制范圍：室溫—95℃   20-95℃

3、主機壓力分辨率：0.001MPa

4、水箱溫度控制: ±0.1℃。

5、主機恒壓范圍：＜設定值的＋2%、－1%

6、水箱溫度均勻性:±0.1℃。

7、主機恒壓：不低于±1% 

8、水箱溫度分辨率: 0.001℃。

9、計時范圍：0～9999.59小時

10、計時：≤0.1%

11、水箱配短路保護裝置，材質為不銹鋼

12、水箱保溫層厚度： 大于83mm，小于95 mm

13、試驗工位數：?jiǎn)螜C(jī)多100路

14、壓力控制系統電源：AC220V、1.5kw

15、溫度控制系統電源：AC380V、18kw

恒溫水箱性能

1）材質內膽為2mm厚不銹鋼板。

2）85mm以上厚保溫層，并有減少熱橋（短路）措施，保溫省電。

3）器件均為不銹鋼（管路、管件、加熱器、銅閥門等）。

4）格蘭富循環泵，大水箱循環能力135l/min（額定）。

5）控溫系統采用品牌漏電保護裝置及時保護人員。

6）水箱可以自循環，也可以連接外循環系統。

7）水箱自帶加熱控制系統，制冷系統。

8）介質箱端口: 根據用戶需要訂制。

關鍵部件配置

Instrument featur:

The static hydraulic tting machine is applicable to the determination of the time of ristance of the thermoplastic pipe under the long-term hydrostatic tt of various plastic pip, hydraulic instantaneous burst tt and long-term constant prsure.

Earlier I do pipe inspection equipment company is a domtic company, the most symbolic is the partial prsure of technology, our company is to use the instrument and computer control, electric control valve, multi-function control.

Some are still unique: the whole nation has mastered the technique of partial prsure control (different prsur) earlier.

The whole country US the upper and lower computer (double computer) control mode earlier.

The same voltage control mode was adopted earlier in the country.

It is the first choice of rearch institut and quality vision department.

Meet the standard:

GB/t6111-2003 "tt method for internal prsure tt of thermoplastic pipe material for fluidic transport"

GB/t"method for the prsure tt of hydraulic instantaneous blasting of plastic tubing for fluid conveying"

GB/T18742.1-2002 "cold and hot water polropylene part ii: pip"

GB/T18742.2-2002 "cold and hot water polropylene part ii: pip"

GB/T18742.3-2002 "cold and hot water polropylene part iii: pipe fittings"

GB/TPE pipe for water supply

GB/T15558.1-2003 "PE pipe for the buried of gas"

GB/T18992.1-2003 "general principl of cross-linking polyethylene pipe system for cold and hot water"

GB/T18992.2-2003 "cold and hot water crosslinked polyethylene pipe system pipe"

GB/T10002.1-2006 "water supply hard polyvinyl chloride (PVC - U) pipe"

GB/T10002.2-2006 "water supply hard polyvinyl chloride (PVC - U) pipe fittings"

GB/T18993.1-2003 "chlorinated PVC piping system for cold and hot water"

GB/T18993.2-2003 "chlorinated PVC piping system for cold and hot water"

GB/T18992.1-2003 "pipe fittings for chlorinated polyvinyl chloride pipe in cold and hot water"

GB/t18997.1-2003 "aluminum plastic composite prsure tube welded aluminum pipe"

GB/T18997.2-2003 "aluminum plastic composite prsure tube aluminum tube butt welding"

ASTM D1598, ASTM D1599

Performance introduction:

1), each a piece of "microcomputer control unit" (true branch control - to prevent a system to control the multiplex system problems affect all each - now some products with more than a set of systems and control) microcomputer control, can be in the upper computer system do not boot separate setting and control under the condition of the road parameters such as prsure, precision and time;

Real-time display prsure, time, state (8) and data storage of each parameter.

(to prevent data loss of data when the computer is offline -- some products are equal to this time tt when the product is offline);

At the same time, it discriminat the tt state of prsure, prsure, prsure, prsure, overprsure, operation, ending, leakage and bursting.

Automatically discriminat the time parameters of "effective tt time" (the time in which prsure is in the control tolerance zone) "invalid time" and "remaining time".

Automatically adjust at the same time set the "time" and "effective time" relationship to tt only in "effective time" "set time" tt to automatic s (prevent night holiday period, such as "down time" "invalid time" system in time can't s)

2) solenoid valve, two branch each.

The adoption of advanced synchronization with Germany, Denmark, on the way, a liter piezoelectric valve according to procedur and tt, change the operating frequency and action time rpectively, the rapid and exact make PE large diameter sample fill prsure.

To equipment applicable range (20-630 Ф Ф PE tube) of high precision in prsure control (better than + / - 1% up to + / - 0.001 Mpa).

3), Denmark import water prsure station a, than domtic water use hydraulic tt pump and some manufacturers products with gas drive pump (with gas drive water) flow, better performance, longer life, low noise pump (source).

4) the high-precision sensor of the space department has a set of 0.001Mpa and the hight prsure accuracy to set a set value of 0.001 Mpa.

5) there is also a number of pipeline one-way valve for each road.

6), multi-line, multichannel dial liquid crystal display storage communications (including U disk storage), communication protocol, broader performance in May and computer (PC) and programmable controller (PLC), touch screen display terminal communications

7) brand computer,

Featur and composition:

1, the characteristics of

1) continuous and uninterrupted work ensur the integrity of the tt;

2) it is independent and easy to operate and maintain.

With separate 3), prsurized water tank, the use of water through the main pump to fill prsure in pipe specimen, ensure the pipeline of water quality, improve the piping components (such as solenoid valve, needle valve, globe valve, check valve) service life;

4), the use of independent rearch and development, unique, pulse duty ratio fill prsure technology, to patch prsure booster links and link together, a branch was decreased, and the device that will reduce the risk of damage of the device;

5) use Taiwan piston pump, low noise, quick filling, short working time, and indirectly improve the service life of plunger pump;

6) the instrument control is equipped with a PC (that is, the computer), and the serial port is connected with the instrument.

A, can draw prsure time curve,

B. Can query the voltage control value at any time in real time,

C, printable output report,

D, can replace artificial duty, when unattended (such as night) automatically record prsure value;

E, the computer machine can s work at any time, the instrument still continu to work.

2. Dcription of equipment:

The tt machine consists of prsure control system, prsure source, constant temperature media box, fixture and computer.

1) the prsure control system consists of two parts: the prsure line and the electric appliance in the control cabinet.

The prsure pipeline consists of accumulator, solenoid valve, one-way valve, filter, manual needle valve and connecting pipe.

The electrical control part consists of dial control prsure gauge, temperature control instrument, prsure sensor, solenoid valve, relay, overheat protector, various switch and so on.